Three Ways to Accelerate Wireless Design Certification

Matt Schellin Matt Schellin, RF Engineering Manager, Digi International
August 11, 2022

Prototyping and developing wireless products can be a lengthy and challenging process, depending on whether you start with building blocks, or work from a chip-down design, as well as the expertise you have on your team and other factors.

So — you’ve designed your wireless product, and it's time to build your prototype and get your product into production because time is of the essence, right?

Yes, but first you want to think about certification requirements. If you take a few important steps in the early stages, you can increase your chances of success in the certification process and actually improve your time-to-market.

 

There are a few paths when designing your wireless product: use a pre-certified module, non-certified module or design your own wireless transmitter from scratch. Each path has its own complexities and design time.

Using a pre-certified module from Digi International is one of the quickest ways to market. The module is already designed and certified for some of the major countries in the world. This is usually the best path forward if you are not familiar with wireless design or the certification process.

 

Key Considerations for Pre-Certified Wireless Components

Wireless product design
There are a few important things to note when development with pre-certified modules:

  • One caveat to using a pre-certified module is that you need to use it in your end product as it was certified and noted in the grant. Typically this means that the end product needs to provide a separation distance from all persons and must not be co-located with another transmitter within the device. Your end product will require extra testing and certification if your end product is going to be body worn or have another transmitter build in.
  • Another caveat is the countries that the module is certified for. If your end product is going to be used in a different country, then your product or module will require that new country certification.
Digi’s Wireless Design Services team can help with your end product for these caveats.
 

Three Key Ways to Accelerate Wireless Design Certification

Electronics lab
Here are some important practices that can get your product to market faster, with fewer board spins and at a reduced cost:

  1. Build certification success into your design: It’s critical to understand the standards and tests involved in the certification process before you start to design. In Digi WDS, we often see situations where an organization launched into development without clear understanding of requirements or RF design best practices, only to have serious emissions issues with their electronics, or performance problems with their antenna, resulting in certification failures at the end of their development cycle and subsequent board spins.

    The exact certification requirements vary depending upon the regions your end product will support. Certification requirements also depend on your communication method, as cellular products must pass additional certifications. See the related post, Preparing for Wireless Design Certification, to read about the most common certification requirements.

  2. Test at critical junctures: Testing aspects of your design along the way is a great practice. The goal is to be certification-ready and pass the first time in the actual certification process. Work with your test lab at phases throughout product development to do pre-scans and spot-check high risk areas. While this process can result in changes to your PCB layout and antenna implementation, the earlier you can identify issues, the lower your risk of failure in the formal certification process.

  3. When the going gets tough, outsource key aspects of your development: It is rare for engineering teams to have a full suite of experts in every aspect of design, prototyping, testing, building, and certification. Not to mention all of the critical equipment required for success at each phase along the way.

    If you run into challenges or just need some assistance to put your best foot forward, a professional wireless design service like Digi’s WDS team can help. We have a full team of experts in all aspects of designing, building BSPs, testing, preparing for manufacturing and of course supporting designs that pass certification the first time.
The support you require may include anything from advising on your basic design principles to providing a complete reworking of a design that is not passing certifications. While the best possible strategy is to design for certifications to avoid failures, even failing designs can be rescued and turned into successful products that pass certifications with flying colors.
 

Next Steps

Did You Know? Digi’s Wireless Design Services Team Can Help You Pass Certifications on the First Try.
See the WDS Certification page

Related Content

Digi Earth Rover: Inspiring STEM Robotics Digi Earth Rover: Inspiring STEM Robotics The Earth Rover is a STEM educational robot that demonstrates the power of cellular IoT for remote devices. It is remotely... READ BLOG Easy-to-Integrate Voice Control for Embedded Design Easy-to-Integrate Voice Control for Embedded Design Introducing Digi ConnectCore® Voice Control, a solution that enables voice processing on devices at the network edge with no... READ BLOG Accelerate Device Design Without Sacrificing Security Accelerate Device Design Without Sacrificing Security Since industrial IoT devices often have long lifecycles, their security needs to be designed with the complete lifespan in mind. VIEW PDF Digi XBee Ecosystem | Everything You Need to Explore and Create Wireless Connectivity Digi XBee Ecosystem | Everything You Need to Explore and Create Wireless Connectivity The complete Digi XBee ecosystem includes rf modules, code libraries, and the award-winning tool suite, Digi XBee Tools. VIEW PRODUCTS Accelerating Wireless Development with the Digi XBee RF Ecosystem Accelerating Wireless Development with the Digi XBee RF Ecosystem Embedded developers have multiple choices today in embedded development tools for wireless connectivity in IoT applications. It... RECORDED WEBINAR Certification Design Services Certification Design Services We can guarantee a passing grade, where others fail 80% of the time. GET STARTED Going Global with Your Cellular Deployment Going Global with Your Cellular Deployment As the Internet of Things becomes increasingly popular, more companies are looking to monitor and track their assets across the... READ BLOG NVdrones Gives Developers a Platform to Quickly Create Drone Applications NVdrones Gives Developers a Platform to Quickly Create Drone Applications The core idea for creating the XBee was to create a module for wireless communications that gives our customers the option to... READ BLOG Digi ConnectCore 8M Nano Digi ConnectCore 8M Nano Embedded system-on-module based on the NXP i.MX 8M Nano processor; designed for longevity and scalability in industrial IoT applications VIEW PRODUCT Five Tips for Successfully Developing IoT Applications Five Tips for Successfully Developing IoT Applications This field guide provides an overview of five ways to improve the design of your wireless IoT product, get to market faster, and increase the reliability of your solution. VIEW PDF FDA Guidance for RF Wireless Medical Devices FDA Guidance for RF Wireless Medical Devices To ensure the proper functioning of wireless medical devices, the FDA regularly issues requirements and guidelines. This white paper describes their impact on product designs in the healthcare market, and how to ensure you meet your go-to-market goals. VIEW PDF Compliance Design & Certification for IoT Cellular Applications Compliance Design & Certification for IoT Cellular Applications VIEW PDF Build vs Buy: Navigating the Choice Build vs Buy: Navigating the Choice In this white paper, we help you to evaluate the best way to optimize your IP and make the right build-vs.-buy decision to meet your goals. VIEW PDF